![myer ride pinbox myer ride pinbox](http://4.bp.blogspot.com/-O4nMBBZYZL4/TdIhq7vBolI/AAAAAAAAEP0/rstwpJjavXs/s1600/honda.jpg)
- #MYER RIDE PINBOX PDF#
- #MYER RIDE PINBOX INSTALL#
- #MYER RIDE PINBOX DRIVER#
- #MYER RIDE PINBOX CRACK#
5th wheel hitch,fifth wheel hitch, 5th wheel pinbox. It will also help greatly with "Chucking" and relieves a lot of stress on the 5th wheel frame. The Flexair really helps to smooth out the ride of your 5th wheel and truck. Model L05 for mount 1621 see photos for hole patter. a few scratches and dings that do not affect use.This is the best replacement unit to reduce front to back slap and reduces the jarring from pot holes in the road. This is a like new replacement 5th wheel Air Ride Flex unit.
#MYER RIDE PINBOX CRACK#
If you hit the Pin Assembly to hard you will more then likely crack the plastic bushings in the "Link Kit". Do both sides the same, a little bit at the time. Go really easy here, just nice gentle little taps. Once you have the "Pin Assembly back in place, it's time to insert the "Pin Assembly". Just go really easy when you lower the pin box down so you do not damage the "Link Kit" or the "Urethane Bumpers" When you have replaced the bushings or the whole "Link Kit", lower the pin box down again. Once you have the "King Pin Base" removed and resting on the table and the pin box lifted up you can easily take each link off and inspect the bushings. Pin Assembly removed from the Glide Ride Pin box Now take some more pictures so you see how the "Link Kit" is put together, especially how the plastic bushings are installed, top and bottom is opposite. Use the jacks on the trailer again to raise the pin box up. Once you have the "Pin Assembly" remove on both sides the "King Pin Base" will sit nicely on your table and the "Link Kit" will be partly exposed.
#MYER RIDE PINBOX DRIVER#
You more then likely have to use a flat screw driver to get them started, working from side to side, just work back and forth easy. Work from side to side (front - back) removing the Pin Assembly The "Pin Assembly" holds the whole "King Pin Base" in place. There is a "Pin Assembly" on each side of the pin box. Once you have removed the "Serrated Flange Bolts" it is time to remove the "Glide Ride Pin Assembly". These bolts are really torqued up so warm up your biceps or do what I did, use an impact wrench. The "Glide Ride King Pin Base" is now just touching the table and it is time to remove the "Serrated Flange Bolt", one on each side of the pin box. If you do not have a table like mine where the king pin fits in the middle, use a flat small table and make a small frame with some two by fours.
#MYER RIDE PINBOX INSTALL#
It is not super heavy but it is a bit awkward to handle, especially when you install it back in again. Then I used the front jacks on the trailer to lower and raise the pin box, so when I removed the "Glide Ride Pin Assembly" the "Glide Ride King Pin Base" would not just drop down. So the way I did it, I backed up the truck and set an adjustable utility table on the tail gate. This will help if you not to get delayed at all. Use the camera on your phone to take pictures as you go along. All the parts that are in quotation marks ( " ) correspond with this parts list.
#MYER RIDE PINBOX PDF#
However I only received the plastic bushings.īefore we go any further here is the parts list in a pdf file format, just so you know what I'm talking about. When I talked to Demco they said that they only sell a complete Link Kit ( four links and four bushings).
![myer ride pinbox myer ride pinbox](https://4.bp.blogspot.com/_annTPGBcsB4/TAn8oV3XHmI/AAAAAAAADpo/YJVxZKse8ro/s1600/IMGP2563b.jpg)
King pin lowered on table by using the front jacks.Ĭontacted my dealer and the parts came in short time and were of course replaced under warranty. The only thing I can think of is that when the pin box was being assembled, someone hit the "Glide Ride Pin Assembly" way to hard, and it was not properly lined up therefore breaking the bushings. When I installed my new Glide Ride Pinbox, I noticed that two of the plastic bushings that fit into the Link Kit were broken. Back up your truck and use an adjustable utility table